Step 2: Insert a USB drive. FAT32 has a file size limit of 4GB while the installation ISO now contains one file that is larger.Step 1: Download & install Etcher on Windows 10/7. The main reason for this is because macOS supports only FAT32 as filesystem that is compatible with Windows (and ExFat but that causes issues to boot from). Plug a USB drive into your Mac and open Disk Utility.Unfortunately, since some time, it became a bit more complicated to create this USB drive from macOS. If you’ve downloaded Windows 10 ISO image, here is how you can create a bootable Windows installer USB on Mac using UNetbootin. UNetbootin is a free, open source utility that allows you to create bootable USB drives on Windows, Linux, and Mac OS X.The copy process may take a little while, depending on the speed of your thumb drive. Now copy all files to your USB drive (e.g. When the Windows 10 ISO download is done, double click the file to open it. Step 6: Flash Complete, Eject the drive.Create a bootable USB drive. Step 5: Flash to create a bootable USB drive. Step 4: Select the connected USB flash drive on BalenaEtcher.
You will need one that is at least 8GB. Iso file on your Mac: Prepare the USB driveWhile the ISO is downloading, we can prepare our USB drive. When you open this link on macOS, it should show you the ability to download the ISO rather than the Media Creation tool, which is shown when opening the same on a Windows-based PC.Choose for Windows 10, then select the preferred language, go for the “64-bit Download” and wait for the download to complete to get the. Download the Windows 10 ISOLet’s start by downloading the ISO from Microsoft. Note that some steps involve use of the sudo.To overcome this, we will need to use a tool, Wimlib, which is able to split this file in two parts. Dell se198wfp driver for macCopy all smaller files to the USB driveAfter the previous step, our USB drive is prepared. Finally click “Erase” to complete the process. In the dialog, enter a name for the drive (WINUSB here), choose to format as “MS-DOS (FAT)” and “Master Boot Record” as scheme. This is a tool that is developed to work with, and modify. Unfortunately we have to work around that by splitting the file in two parts, smaller than the limit of our file system on the USB drive.To accomplish this, we can use Wimlib (). As you can see, the sources folder contains one large file: install.wim which is over 4GB and will not fit on the FAT32-formatted USB drive:We will take care of that later so for now, copy all remaining files to the USB drive using Finder.I typically start by copying all separate files and folders, except for the sources folder:Then I create the sources folder and copy all files from sources with the exception of install.wim: Prepare to split install.wimSo far things were pretty straightforward and if it wouldn’t be for that large file it would be a piece of cake. “/Volumes/CCCOMA_X64FRE_EN-GB_DV9/sources/install.wim” which is the source file to split. “split” to indicate that we want to split this larger file In the same or a new Terminal session, execute the following: ~ % wimlib-imagex split /Volumes/CCCOMA_X64FRE_EN-GB_DV9/sources/install.wim /Volumes/WINUSB/sources/install.swm 4000Splitting WIM: 4654 MiB of 4654 MiB (100%) written, part 2 of 2Finished splitting "/Volumes/CCCOMA_X64FRE_EN-GB_DV9/sources/install.wim"In the command above, we told to execute the wimlib-imagex tool (part of Wimlib) and passed some arguments: ~ % /bin/bash -c "$(curl -fsSL )"=> Checking for sudo access (which may request your password).Once Brew is installed, we can use it to install Wimlib: ~ % brew install wimlib=> Pouring wimlib-1.13.4.big_sur.bottle.tar.gz□ /usr/local/Cellar/wimlib/1.13.4: 65 files, ~ % Split install.wim and get it on the USB driveNow that we have Wimlib installed, we can use it to split the large install.wim file and copy it to our USB drive. As is instructed on the Brew website, copy and paste the mentioned line in a terminal and execute it. Size of the destination file, so the file will be split in a part of 4000MB and the rest.After this command completes, you can see that now two files were created on the USB drive:The Windows 10 installer knows how to deal with these and will just work fine.That should be all you need to create a bootable USB drive for Windows 10 installation. Adjust this as well when you chose something different earlier. As with the ISO name, here WINUSB is the volume label I gave to my USB drive when erasing it with Disk Utility. “/Volumes/WINUSB/sources/install.swm” the destination of where the split files should end. Just do ls /Volumes from the terminal to see what is there. Make Usb Boot Drive On Windows Driver Installation UsingBoot from the USB driveAs the final step, now that the USB drive is prepared, with or without additional drivers for your Mac, you can boot from it.On a regular PC, this is usually done by pressing a key at BIOS time to bring up a boot menu (F11 is often used for this) or, for some older BIOS, by changing the boot order from the BIOS setup. The files got downloaded as a subfolder of brigadier-master as WindowsSupport.dmgAll that is left to do is to navigate to the folder using Finder, then to open WindowsSupport.dmg to mount it and to copy those files to the USB drive:After going through the installation, executing BootCamp/setup.exe will install most of the required drivers or at least enough to continue the rest of the driver installation using Windows update. If you want to download the required drivers for another model, you can simply pass it using the –model parameter.
0 Comments
Leave a Reply. |
AuthorDanielle ArchivesCategories |